Power supply:
100 to 260 V ac
(50/60~) Mains supply via IEC connector
or
9 to 28 V dc, via XLR4 (1 = -ve, 4 = +ve)
300mA with 8 active beltpacks
600mA with 8 active beltpacks and charging internal back-up battery.
Internal back-up supply:
Back-up time with 8 active beltpacks
is 4 hours.
Audio:
[Note: 0 dBm
relates to 1mW (775mV) at 600Ω
Line input level : 0 dBm balanced
600Ω
Line input minimum (VOX control) : –23 dBm balanced 600Ω
Line output maximum : +4 dBm (preset to 0 dBm) balanced 600Ω
Audio connectors are standard XLR3 (Pin 1 = ground, pin 2 = hot, pin 3 = cold)
RF:
Standard DECT frequencies,
1880 – 1900 MHz
120 Traffic channels available
Integral aerial, licence exempt.
Dimensions (excluding
connectors):
175 x 130 x 80 mm
Weight:
Less than 750g including back-up battery
Temperature range:
-10° to +50° Celsius
Mounting:
To be wall or stand mounted vertically at an optimum height of 1.6m above floor
level, on a non-metallic surface for optimum radiation pattern.
Approvals:
R&TTE - TBR6 (CE0681)
E.M.C. – EN301 489-1/-6, EN50081-1, EN50082-1 (CE0681)
Environment – IP52 approved
Radiation pattern:
* Please note this is preliminary information, and changes to improve this specification are possible in the imminent future. Please check the website regularly for up to date information.
E&oe 26th
November 2003, JM
Power supply:
Nickel Metal Hydride internal
rechargeable battery – 3.6V 1500mAh
Standby time (with beltpack registered to base unit)
> 100 hours
Active time in conference ( talk time) > 15 hours
The above times relate to a battery being fully charged initially, the
Charge time being approximately 5 hours.
It is possible to power the beltpack from three
standard AA size alkaline cells, for which a special battery container is
required.
Receiver:
Normal mode:
Maximum speaker voltage 4.5V peak to peak
Distortion < 10%
Recommended load impedance 16 – 100 Ω
High level mode: Maximum speaker voltage 12V peak to peak
Distortion < 10%
Recommended load impedance 16 – 100 Ω
Receiver Frequency response:
|
Transmitter:
RF:
Standard DECT frequencies, 1880 – 1900 MHz
120 Traffic channels available
Integral aerial, licence exempt
|
Transmitter Frequency response:
|
Dynamic Mode:
Noise cancelling type recommended
Microphone impedance : 200~300 Ω
Microphone sensitivity : -60dB (at
L=50cm)(0dB=1V/Pa, 1KHz)
Electret Mode:
Noise cancelling type recommended
Microphone impedance : 1000~2000 Ω
Feed resistor/ voltage : 2KΩ/2.8 Volts.
Headset connection:
|
|
|
|
Approvals:
R&TTE - TBR6 (CE0681)
E.M.C. – EN301 489-1/-6, EN50081-1, EN50082-1 (CE0681)
Environment – IP52 approved
* Please note this is preliminary information, and changes to improve this specification are possible in the imminent future. Please check the website regularly for up to date information.
Weight:
200g including battery,
excluding headset.
E&OE
26th November 2003, JM
